|
|
 |
|
|
|
|
System Components 
At the heart of the Hyproof waterproofing system is a Coal Tar Elastomeric (CTEM)
membrane that is a combination of coal tar, PVC, and Elvaloy®, a high molecular
weight PVC plasticizer. This unique combination of materials gives the membrane
unequaled properties making it ideally suited for waterproofing applications.
Tough, durable, and extremely chemical resistant, the membrane also is impervious
to mold, mildew, rot, and root penetration. Our membranes and cloaks can be
joined by either hot air weld which fuses the membrane together, or the strong
covalent bond provided by our high performance Structural Sealant. All our components
work together to provide tight, durable, and complete protection not just against
the water, but all other environmental contaminates.
Hyproof SA
(Self Adhered) Membrane |
| A self adhered, fully adhered, CTEM waterproofing membrane intended
for use over primed smooth, dry substrates. The bottom of the sheet is
fully coated with SBS-modified asphalt with a dry selvedge edge for hot
air welds. Suitable substrates include, but are not limited to, wood,
masonry, and dry concrete. |
Hyproof SA2 Membrane |
| A self-adhered CTEM membrane. In contrast to our Hyproof SA product,
the adhesive is applied over 50% of the bottom of the sheet. This product
is used as the second ply in our 20 year warranty systems. It also has
a dry selvedge edge for hot air welds. |
Hyproof GL (Grid Lock) Membrane |
| An uncoated CTEM waterproofing membrane that is installed onto ribbons
of Membrane Adhesive laid in a grid pattern. It is intended for use over
smooth surfaces that could be moist or, in retrofit projects, covered
with an older existing waterproofing system. Possible substrates include
concrete that has not fully cured or an old hot-applied asphalt or coal
tar waterproofing system. Contact Hyload for further guidance regarding
acceptable substrates. |
Hyload Structural Sealant |
| A moisture cure, moisture insensitive, high performance polyether sealant.
It will covalently bond to both Hyproof membranes and cloaks, in addition
to aggressively bonding to almost all commonly used construction materials.
In addition to bonding membranes and cloaks, Structural Sealant is used
to seal any exposed termination of the Hyload waterproofing system. |
Hyload Membrane Adhesive |
| A moisture cure, moisture insensitive polyether adhesive that is used
to adhere Hyproof GL to substrates. Membrane Adhesive is typically applied
in a 12” o.c. grid (checkerboard) pattern so that it will limit
the lateral migration of water. It will bond to almost all possible substrates
including uncured concrete, masonry, asphalt, and coal tar. |
Hyload Trowel-On Membrane (TOM) |
| A solvent-free waterproofing mastic that can be applied in beads from
a 28 oz. caulking tube, or trowel-applied from 2 or 5 gallon pails. Hyload
TOM cures by exposure to ambient moisture. It is suitable for use in both
above and below grade applications. Among other uses, Hyload TOM is used
to form fillets for inside corner applications of the Hyload waterproofing
system. It is also used to affix Hyload Cloaks into place. |
Hyload Cloaks |
| Pre-formed inside and outside corners for installation with the Hyload
Hyproof waterproofing system. Hyload TOM is used to affix the cloaks into
place. The cloaks can be bonded to Hyproof membranes with either Hyload
Structural Sealant, hot air welding, or a combination of both. |
Hydrain Drainage Boards |
| Provide pre-formed engineered drainage that will minimize hydrostatic
build-up on Hyload waterproofing systems. Hydrain comes in (typically)
4’ x 50’ foot sections for quick and easy installation. |
Hyglass Protection Board |
| A tough and dense fiberglass and asphalt composite board that offers
membrane protection from many of the physical abuses that are common during
the construction and waterproofing process. Typically sized at 4’
x 5’ and approximately ¼” thick, it is quick and easy
to install. Other sizes/thicknesses are available. |
|
|
|
|
|
|
